Find out how to use a pipe twisting machine

Pipe bending machine is usually an important modern curved naff processing equipment, which is based on the vector theory, using computer control, to complete any space for that three-dimensional tube to meet up with users requirements. It is important to know the correct us going for a roller bending machine.

• Operation mode associated with pipe bender
  

• Suggestions of using for tv bender

Operation mode with pipe bender

1. Trunk up. Check the voltmeter within the transformer (380V and 220V). Check the barometer (0. 4--0. 6) Mp around the triplet. How to adjust the barometer: lift the black knob just earlier mentioned the triplet, clockwise or counterclockwise to adjust the environment pressure.

2. Manual. Reset and return for you to origin

Methods as down below:

1. Click the reset button within the lower left corner intended for 3 seconds-point feeding-point ahead 2 seconds-point elbow-point ahead 2 seconds-point origin. Directly. The red ready term appears right above, indicating the fact that origin is returned to completion. If not ( the trolley as well as pipe bender do possibly not move), please repeat the procedure until the word set appears.

Replace your mold

1. There are four varieties of molds, namely: round form, sliding mold, clamping form and clamping jaw

2. Install the molds into the corresponding positions under this manual interface, and ensure potentially they are on the same middle line.

Note: Ensure the fact that material cannot be pulled or rotated while in the clamping mold and the clamping jaws; the special attention needs to be paid to one- Make sure you do it independently.

Several: Programming

1. Click programming inside the upper right corner to help enter the programming user interface;

2. Click New directly below-click Save while using bottom corner-enter the file name in the product and confirm-click yes;

3. Click XYZ in the lower left corner-point increase-input your XYZ coordinate value from the first line-point increase-input the XYZ coordinate of the second line...until every one of the coordinate values are typed in, click the upper left corner in the punch radius, Enter the R value with the mold (that is, the type and model of the R angle);

4. Click the conversion in the lower left corner, check the Y worth and C value within the program (note that the Y value can not be negative, and the C value cannot be greater than the maximum angle from the circular mold)

5. Click the preview while in the lower right corner to determine whether the 3D pulling processed by the program is similar to the drawing or sample.

Four: manual

1. Click Manual within the right to enter that manual interface;

2. Just click the feeding switch immediately above, pull down the cart along with your hand until the upper jaw in the trolley touches the circle mold, then gently push the small

Five: parameters

1. Click the parameter on the right to enter the particular parameter interface;

2. Just click the table below your circular mode interference quit, enter the A cost just noted-point confirmation; click on the table below that sliding mode interference stop, enter the B benefit just noted-click confirmation;

3. Click programming in the upper right corner to input the programming interface; click save while in the lower right corner-click confirm-click of course;

Six: automatic

1. Make sure you enter the set productivity

2. Click to run until the equipment runs

3. When the program appears round mold interference in the operation of running, please don't jog the automatic program, write down the value a inside second table in the upper left corner, write down the extra worthiness b in the true feeding position table.

4. Click programming on the right to enter the legitimate interface, click save within the lower right corner-click confirm-click certainly; click manual-click reset intended for 3 seconds-click automatic-click operate, (see if it is actually running normally. If not necessarily, please increase the he value, To ensure the maximum value is in 30, repeat the SEVERAL process)

Tips of utilizing for tube bender

Inspect the produced product to find out if it is qualified (if its unqualified, please modify it in the programming: Y stands for length; B stands regarding rotation; C stands pertaining to angle), until the manufactured product is qualified. Then Click Manual-click shutdown around the right corner, when that screen appears black or even blue, the power is usually turned off.

Zhangjiagang King-Macc Machinery Making Company can provides the actual satisfied tube bending into the customers according to the accumulated designing experience and much more experiments.