On the web use a pipe twisting machine

Pipe bending machine is definitely an important modern curved plastic material processing equipment, which will be based upon the vector theory, utilizing computer control, to complete any space with the three-dimensional tube to fulfill users requirements. It is vital to know the correct make use of a roller bending machines.

• Operation mode associated with pipe bender
  

• Tips of using for tube bender

Operation mode associated with pipe bender

1. Kick out up. Check the voltmeter on the transformer (380V and 220V). Check the barometer (0. 4--0. 6) Mp around the triplet. How to alter the barometer: lift that black knob just on top of the triplet, clockwise or counterclockwise to adjust the environment pressure.

2. Manual. Reset and return in order to origin

Methods as down below:

1. Click the reset button from the lower left corner for 3 seconds-point feeding-point ahead 2 seconds-point elbow-point send 2 seconds-point origin. Directly. The red ready word appears right above, indicating that the origin is returned to completion. If not ( the trolley and also the pipe bender do possibly not move), please repeat doing this until the word prepared appears.

2. Replace the mold. There are four sorts of molds, namely: round mould, sliding mold, clamping pattern and clamping jaw. Install the molds to the corresponding positions under the particular manual interface, and ensure that they're on the same facility line.

Note: Ensure that the material cannot be pulled or rotated while in the clamping mold and this clamping jaws; the special attention should be paid to one- You should definitely do it independently.

Three: Programming

• Click programming inside upper right corner to help enter the programming software;

• Click New directly below-click Save considering the bottom corner-enter the file name from the product and confirm-click without a doubt;

• Click XYZ in the lower left corner-point increase-input that XYZ coordinate value on the first line-point increase-input the XYZ coordinate in the second line...until all the coordinate values are typed in, click the upper left corner with the punch radius, Enter the R value from the mold (that is, the dimensions of the R angle);

• Click the conversion inside lower left corner, check the Y value and C value inside program (note that the Y value is not negative, and the C value can not be greater than the maximum angle of the circular mold)

• Click the preview inside the lower right corner to view whether the 3D pulling processed by the program is related to the drawing or piece.

• Click Manual within the right to enter that manual interface;

• Push the feeding switch straight above, pull down the cart using your hand until the upper jaw with the trolley touches the around mold, then gently push the tiny

Parameters

1. Click the parameter for the right to enter the parameter interface;

2. Simply click the table below that circular mode interference quit, enter the A valuation just noted-point confirmation; press the table below the particular sliding mode interference halt, enter the B price just noted-click confirmation;

3. Click programming in the upper right corner to input the programming interface; click save inside lower right corner-click confirm-click indeed;

Automatic

1. I highly recommend you enter the set result

2. Click to run until the gear runs

3. When the program seems round mold interference in the process of running, please never jog the automatic program, write down the value a while in the second table in top of the left corner, write down internet b in the genuine feeding position table.

4. Click programming on the best to enter the programming interface, click save in the lower right corner-click confirm-click of course; click manual-click reset to get 3 seconds-click automatic-click work, (see if it is actually running normally. If definitely not, please increase the he value, To ensure the fact that maximum value is in just 30, repeat the 5 process)

Tips of implementing for tube bender

Inspect the produced product to check out if it is qualified (if it is unqualified, please modify it from the programming: Y stands for length; B stands for rotation; C stands intended for angle), until the made product is qualified. Then Click Manual-click shutdown for the right corner, when the particular screen appears black or perhaps blue, the power can be turned off.

Zhangjiagang King-Macc Machinery Creation Company can provides this satisfied tube bending into the customers according to the accumulated designing experience plus more experiments.