Using pipe bending machine

Today, the industry is formulated. No matter what sort of machine equipment, fitness tools, furniture, etc.,There are almost structural steel pipes and oil pipes pertaining to oil, gas, fluid infusion, and they occupy a very important position in fitness apparatus. The large number associated with various tube types as well as their complex forms have brought many difficulties towards processing of catheters.

• Safety safe practices for tube bender functioning

• Steel bending machine working procedures

• Regularization of pipe bending machine

Safety steps for tube bender functioning

1. When the machine tool is started, give any focus on enter the swept range with the rotating arm.

2. When the machine tool is doing the job, all personnel are prohibited from entering the space swept by the boom and pipe bender fittings!
   

3. The hydraulic system belonging to the roller bending machine instrument adopts YA-N32 ordinary hydraulic essential oil (formerly No. 20), which really should be replaced once a 12 months under normal circumstances, and the oil sift must be cleaned as well.
   

4. When adjusting the machine tool (mold), the adjuster have to press the button in order to adjust. Never make adjustments by one person within the machine and the other about the control cabinet.
   

5. The core rod should be removed when adjusting the machine tool or driving a great empty car.
   

6. The pressure belonging to the hydraulic system should not be more than 14 Mpa.
   

7. When manually adjusting the velocity of the side thrust cylinder, the rotating arm really should be adjusted when it is usually rotated to ≥900. The adjustment speed is synchronized when using the linear speed of the edge of the rotating elbow style. It is forbidden to push the side pushing faster than the line of the edge of the rotating mold while in the manual state. speed.
   

8. After using the general machine for a period of time, check the tightness on the chain to keep the upper and lower chains small.
   

9. During automatic operation from the core bending mode, prior to pipe bending arm dividends, the operator must ensure that the core head was in the tube, or be sure that the core shaft is not really blocked when the bending arm returns, otherwise, the core head or core rod may be Bend or break.
   

10. After the work ends, cut off the electric power supply and do the best job of cleaning and also lubricating.

Steel bending machine operating procedures

The machine tool must be effectively grounded, and the wire shall not be not as much as 4mm2 copper soft cable. It is not allowed to connect to a power supply voltage exceeding the required range, plug-ins can not be plugged in and out from the plug when power will be on, and the control circuit cannot be tested with a megohm meter, otherwise the nuvi 780 may be damaged.

1. When plugging and unplugging the actual connector, do not pull that wire or cable to prevent the welding from tugging off.
   

2. Proximity switches, encoders, etc. cannot be hit by hard materials.
   

3. Do not hit the display unit together with sharp objects..
   

4. The electrical box have to be placed in a ventilated position, and it is forbidden to operate in dust and corrosive un wanted gas.
   

5. It is prohibited to install or switch the PC input as well as output terminals without agreement.
   

6. When changing the facility supply of the unit tool, the motor rotation direction needs to be reconfirmed.
   

7. The roller bending machine tool ought to be kept clean, and special attention must be paid to that there must be no foreign matter in the sliding grooves such as clamping blocks and slipping blocks.
   

8. Lubricate the chain and other sliding parts regularly.
   

9. The power must be disconnected during cleaning and also maintenance.
   

10. Preparation prior to driving: Check whether the oil degree of the fuel tank reaches the oil level tier, add oil to each lubrication point, turn for the machine to confirm the rotation on the motor, check the fat pump for abnormal appear, and check whether the hydraulic product leaking after turning for the machine (the angle encoder is not allowed Come on);
    

11. Pressure adjustment: use electromagnetic overflow valve to adjust the pressure to ensure that the system pressure reaches the necessary working pressure, generally not greater than 12. 5 Mpa.
    

12. Mold adjustment: mold installation requires mould and clamping block to be centered, clamping block may be adjusted with bolts; booster-style block is centered with mold, booster block will be adjustable; core head is usually centered with mold, loosen core head frame Bolt, make tighter the bolt after adapting the center.

Regularization connected with pipe bending machine

When designing and arranging pipe benders, avoid excessively great arcs, arbitrary curves, compound bends and in excess of 180. The arc. The excessively large arc not simply makes the tooling heavy, but also is limited through the size of the tube bending machine: the design of arbitrary curves and compound bending is incredibly unreasonable, which greatly hinders mechanization and automated creation, making it difficult for operators to get rid of heavy manual labor; In excess of 180. The arc makes the particular steel bending machine struggles to unload the mold.

Zhangjiagang King-Macc Machinery Manufacturing Company can provide the best products.